News

  • 0
  • 0

Global concrete foaming agent market trend 2022-2027 What is Foam Concrete Used For? by Newsb-house

Hasad Foods, the agricultural investment arm of Qatar's sovereign wealth fund, said the government would increase its grain reserves from 250,000 tons to 300,000 tons in the near future, which is enough to feed the population for six months.  

With a lot of deserts, Qatar suffers from water shortages, and Qatar depends on food imports for a long time. Recently, the ongoing tension in Ukraine has caused global food supply tension and rising prices.

In addition to that, the geopolitical situation also affects the supply and prices of many commodities like the concrete foaming agent.

Foam Concrete Properties

Foam concrete is a versatile building material. It is simple to produce and relatively cheap compared with autoclaved aerated concrete. Foam concrete compounds that use fly ash in the slurry mixture are cheaper and have less impact on the environment. The density of foam concrete varies from 200kg/m3 to 1,600kg/m3, depending on the application.  Lighter products can be cut to different sizes. Although the product is considered to be a concrete form (with air bubbles instead of aggregate), its high thermal and acoustic quality makes it a distinct application from conventional concrete. 

 

Foam Concrete Advantage

Foam concrete is no less thermally conductive than wood -- 40cm walls can withstand -30° frost. 

Foam concrete can withstand exposure to fire on one side for at least 3 hours, with an average of 5 hours. 

 

What is Foam Concrete Used For?

Foam concrete can be produced with dry densities of 400 to 1600kg/m3 (25lb/ft 3 to 100lb/ft 3) and 7-day strengths of approximately 1 to 10N/mm2 (145 to 1450psi) respectively.  Foam concrete is fire-resistant and its heat and sound insulation properties make it suitable for a wide range of uses, from insulating floors and roofs to void filling. It is also particularly useful for groove recovery. 

 

Some applications of foam concrete are: 

Bridge method/embankment 

Pipe abandonment/ring filling 

Trench backfill 

Precast block 

Prefabricated wall elements/panels 

Cast-in-place/cast-in-place walls 

Insulation compensation laying 

Insulation floor 

Insulating roof mortar 

Sunken part filling 

Groove back

A sub-base for the highway

Filling of hollow blocks

Prefabricated insulation board

 

Foam Concrete Trends and Development 

Until the mid-1990s, foam concrete was considered weak, non-durable, and had high shrinkage properties. This is due to the unstable foam bubbles which make foam concrete unsuitable for the production of very low density (less than 300 kg/m 3 dry density) and load-bearing structure applications. It is therefore important to ensure that the air ensnared in the foam concrete is contained in stable, very small, uniform bubbles that remain intact and isolated and do not thus increase the permeability of the cement slurry between the voids.

 

The development of synthase-based foaming agents, admixtures to enhance foam stability, and specialized foam generation, mixing, and pumping equipment has improved the stability of foam concrete, allowing the production of lightweight concrete with densities as low as 75 kg/ m3 and a density of only 7.5% of water. The enzyme is composed of highly active proteins from biotechnological sources other than proteolysis. In recent years, foam concrete has been widely used in highways, commercial buildings, disaster relief buildings, schools, apartments, and residential development in Germany, The United States, Brazil, Singapore, India, Malaysia, Kuwait, Nigeria, Bangladesh, Botswana, Mexico, and other countries. 

 

Foam concrete has been studied as a bullet trap for high-intensity US firearms training grounds. This work led to the deployment of the product SACON by the U.S. Army Corps of Engineers, which can be transported directly to a metal recovery facility when it wears out, without the need to separate trapped bullets because the calcium carbonate in the concrete acts as a flux. 

 

The energy absorption capacity of foam concrete was approximated by drop tests and was found to vary between 4 and 15 MJ/m 3, depending on its density. The optimum absorption was estimated from a mixture of 1000 kg/m 3 of moderate density at a ratio of water to cement (w/c) 0.6 to 0.7. 

 

Concrete Foaming Agent Supplier

TRUNNANO is a reliable foaming agents supplier with over 12-year experience in nano-building energy conservation and nanotechnology development.

If you are looking for high-quality CLC foaming agents, please feel free to contact us and send an inquiry. (sales@cabr-concrete.com)

We accept payment via Credit Card, T/T, West Union, and Paypal. TRUNNANO will ship the goods to customers overseas through FedEx, DHL, by air, or by sea.


Affected by the present complex international situation and the epidemic, the future of global financial markets, futures markets, and stock markets is still highly uncertain. For this reason, I suppose the price of the concrete foaming agent would continue to rise.

Inquery us

Our Latest News

Global pce powder market trend 2024-2029 Polycarboxylate superplasticizer advantages by Newsb-house

Polycarboxylate superplasticizer is based on unsaturated polymerizable monomers with active groups such as carboxyl group, sulfonic acid group, hydroxyl group and polyoxene group as raw materials.…

Global graphene powder market trend 2022-2027 Graphene bags significantly reduce platinum requirements for hydrogen fuel cells by Newsb-house

Although hydrogen fuel is a promising alternative to fossil fuels, the catalyst it relies on for power generation is mainly composed of rare and expensive metal platinum, which limits the wide commercialization of hydrogen fuel.…

Global pce powder market trend 2023-2027 Development of polycarboxylate superplasticizer by Newsb-house

According to the different molecular structure, it can be divided into four generations of polycarboxylate series superplasticizer, the first generation is acrylic acid copolymer, the second generation is propylene ether type, the third generation is…